Motorized Two-Way Brass Ball Valve
Why Automate a Ball Valve?
A standard ball valve works fine for manual operation. But for systems that need to operate on a schedule or respond to sensors, manual valves have limits:
- Irrigation systems need water at specific times
- HVAC systems need to respond to temperature changes
- Water tanks need automatic filling
- Remote systems can't be operated by hand
The solution: A ball valve with an electric actuator. The actuator receives an electrical signal and rotates the ball valve open or closed automatically.
The challenge: Most electric valves use complex wiring and require specialized controllers. The 3-wire 2-control design simplifies this.
| Manual Ball Valve | Electric Actuated (This Valve) |
|---|---|
| Requires human presence | Automatic operation |
| No remote control | Remote on/off |
| No scheduling | Timing control |
| Cannot integrate with sensors | PLC/controller compatible |
| Limited to on/off | On/off + timing |
Introduction
Our 3‑wire 2‑control motorized two‑way brass ball valve delivers reliable automatic on‑off control for water pipelines across HVAC, irrigation and water supply systems. This electric ball valve adopts a proven three‑wire control setup: one common wire, one open signal wire and one close signal wire.
- Open circuit: Power feeds to the electric actuator via common wire and open signal wire, driving the ball valve to full open position.
- Close circuit: Power runs through common wire and close signal wire to fully shut down the valve.
Unlike single‑action one‑control motorized valves, this independent dual‑signal design executes open and close commands separately. It achieves fully automatic pipeline switching without relying on extra auxiliary equipment to cut water flow indirectly.
Paired with a robust forged brass two‑way valve body and standard female internal thread connections, this motorized ball valve covers DN15, DN20, DN25 and DN32 sizes. It operates stably with medium temperatures ranging from 5℃ to 90℃, built for automatic liquid water shut‑off applications.
Core Advantages
-
Simple 3-Wire Wiring
Only three wires to connect-common, open, and close. This is simpler than 4-wire or 5-wire systems, reducing installation time and wiring errors.
-
Independent Open/Close Signals
Separate open and close wires allow easy integration with any control system. No complicated signal conversion is required.
-
No Holding Current
The actuator only draws power while moving. Once open or closed, it holds position without consuming power. This reduces energy consumption and heat generation.
-
Forged Brass Valve Body
The valve body is hot-forged, not cast:
- No internal porosity
- Corrosion resistance for water systems
- Long service life
-
Wide Temperature Compatibility
5°C to 90°C range covers:
- Cold water supply
- Hot water heating
- Irrigation (ambient)
- HVAC chilled/hot water
-
Low Maintenance
Simple design with fewer moving parts than solenoid valves. No continuous power draw. Reliable long-term operation.

| Feature | Description |
|
Place of origin |
China |
|
Brand name |
Yunnl |
|
Product Name |
Motorized Two-Way Brass Ball Valve |
| Control Mode | 3-Wire 2-Control (Open/Close independent signals) |
| Applicable Medium Temperature | 5°C ~ 90°C |
| Valve Body Material | Forged Brass |
| Connection Type | Female Internal Thread |
|
Size |
DN15-DN32 |
|
Minimum Order Quantity |
1 |
|
Price |
Negotiable |
|
Packing |
Yunnl standard packing |
|
Payment Terms |
L/C, D/A, D/P, T/T, Western Union,MoneyGram |
|
Delivery Time |
15 Days |
| Applicable temperature | 5℃ to 90℃ |
Wiring and Control Explained
-
The 3-Wire System
Traditional electric ball valves often use 4 wires (two for power, two for signals). The 3-wire system simplifies this:
| Wire Color (Typical) | Label | Function |
|---|---|---|
| Blue | Common | Return path for both open and close |
| Brown | Open | Signal to open the valve |
| Black | Close | Signal to close the valve |
-
How the Actuator Works
- Open command: Voltage applied between Common and Open → actuator motor turns in one direction → ball rotates 90° → valve opens
- Stop: Voltage removed → actuator stops in position
- Close command: Voltage applied between Common and Close → actuator motor turns in opposite direction → ball rotates 90° → valve closes
Stop: Voltage removed → actuator stops in position
-
Control Options
| Control Source | Compatibility | Application |
|---|---|---|
| Time relay | Yes | Simple timing irrigation |
| PLC | Yes | Industrial automation |
| Thermostat | Yes (with relay) | HVAC temperature control |
| Float switch | Yes | Tank fill control |
| Manual switch | Yes | Local override |
Note: The actuator does not require holding current. It only draws power during the opening or closing operation, then stops.
-
Power Supply Options
| Option | Voltage | Typical Application |
|---|---|---|
| Standard | AC24V | HVAC, low-voltage systems |
| Standard | AC220V | Building automation |
| Standard | DC24V | Solar/battery systems |
| Custom | Specify | OEM requirements |
Application Scenarios
-
Agricultural & Greenhouse Irrigation
Use case: Automatic watering on a fixed schedule.
Setup: Time relay sends open signal at 6:00 AM and close signal at 6:30 AM daily.
Value: Consistent watering without manual intervention.
-
HVAC & Floor Heating
Use case: Zone control for heating circuits.
Setup: Thermostat sends open signal when temperature drops below set point; close signal when temperature is reached.
Value: Energy saving through zone-by-zone control.
-
Domestic Water Tank Fill
Use case: Automatic tank filling.
Setup: Float switch sends open signal when water level is low; close signal when full.
Value: No overflow, no dry running.
-
Small Industrial Cooling
Use case: Cooling water circuit control.
Setup: PLC controls valve based on equipment temperature.
Value: Precise cooling water management.
-
Public Restroom Timed Water
Use case: Automatic flushing or timed water supply.
Setup: Timer opens valve at scheduled intervals.
Value: Water conservation through timed operation.
-
Remote Control Applications
Use case: Valve operation from a central control room.
Setup: Switch panel sends open/close signals.
Value: Centralized system management.
Installation & Commissioning
-
Installation Steps
- Check valve size – Ensure DN matches the pipe size
- Apply PTFE tape – 3-5 wraps on the male threads
- Install the valve – Thread into the pipeline
- Orient the actuator – Mount with actuator upright for proper sealing
- Connect wiring – Common, Open, Close (refer to wiring diagram)
- Test operation – Apply open signal, verify valve opens; apply close signal, verify valve closes
-
Important Notes
- Do not apply voltage to both Open and Close simultaneously – this can damage the actuator
- Use appropriate fuse/breaker – protects actuator motor
- Check voltage rating – confirm supply voltage matches actuator rating
- Allow clearance – ensure actuator has space for installation and access
-
Commissioning Test
- Apply power to Common + Open → verify valve opens (check handle position or flow)
- Remove Open signal → valve stays open
- Apply power to Common + Close → verify valve closes
- Remove Close signal → valve stays closed
- Repeat 3-5 times to confirm consistent operation
Troubleshooting Guide
| Problem | Likely Cause | Solution |
|---|---|---|
| Valve does not open | No voltage / Wiring error | Check supply voltage; verify connections |
| Valve does not close | No voltage / Wiring error | Check supply voltage; verify connections |
| Valve moves but no flow | Valve not installed correctly | Check flow direction; verify ball is rotating |
| Actuator hums but does not move | Power supply too weak / Mechanism stuck | Check voltage; inspect for obstruction |
| Valve leaks when closed | Seats worn / Debris in seat | Replace seats; flush system |
| Actuator gets hot | Continuous power applied | Check wiring; actuator should not have holding current |
Product Feature Summary
Yunnl three-wire two-control motorized two-way brass ball valve is a cost-effective automatic electric water valve for global HVAC, irrigation and domestic water control projects. The 3-wire dual-signal control design realizes independent opening and closing operation, DN15-DN32 full size coverage, stable performance under 5℃~90℃ water temperature, simple wiring and low maintenance cost. Flexible payment terms and 15-day fast delivery support small batch sample orders and bulk engineering orders.
FAQ
Q: How long is your product guarantee period?
A: We have three-year guarantee and 24 hours full-time service.
Q: What is your MOQ?
A: We have no MOQ. We have a large warehouse and we promise "Instant Order, Immediate Delivery and No MOQ".
Q: Can you accept OEM and ODM?
A:Yunnal accepts ODM and OEM manufacturing services.
Q: How long is your delivery time?
A: For the items if we have enough stocks, we can send to you immediately. For mass production, we can promise 30-35 days.
Hot Tags: Motorized Two-Way Brass Ball Valve, China Motorized Two-Way Brass Ball Valve manufacturers, suppliers, factory, three wire one control electric ball valve, automated ball valve, Three-wire Two-control Electric Ball Valve, three wire two control electric ball valve

