Internal Thread German Type Y-type Stop Valve
Y-Pattern Globe Valve vs Conventional Straight Globe Valve
Conventional straight-body globe stop-valve adopts Z-shaped internal flow-passage. Medium changes direction twice inside valve cavity, generating large flow resistance and obvious pressure-drop loss. It is widely-used, yet brings disadvantages for circulation-loop projects pursuing low hydraulic loss.
Y-pattern (Y-type) stop-valve arranges valve-stem and sealing seat at approximately 45° angle relative to pipeline axis. Fluid flows through smoother inclined passage. It keeps reliable shut-off performance meanwhile greatly reduces flow turbulence and pressure-drop loss.
|
Item |
Conventional Straight Globe Valve |
German-Type Y-Pattern Stop Valve (This Product) |
|
Internal flow-passage |
Z-shaped, two sharp-angle turns |
45° inclined Y-shaped smooth passage |
|
Hydraulic pressure-drop |
Relatively high |
Significantly reduced |
|
Valve-stem stroke |
Long |
Short working stroke |
|
Open-close operation time |
Longer |
Short open-close cycle |
|
Flow turbulence |
Obvious |
Mild |
|
Best-fit |
General shut-off service |
Circulation loops, heating-system pipelines, throttling occasions |
Product Overview
Yuanlun German-type internal-thread Y-pattern stop-valve is manual threaded globe-type shut-off & throttling valve for plumbing, HVAC heating and light-industrial non-corrosive-fluid piping. Adopting Y-shaped inclined flow-passage structure, it balances reliable sealing performance and low-resistance fluid-transport property.
Valve-stem drives disc to lift and descend to realize opening, throttling and full-closure. Visible stem-lifting position provides direct visual indication for current valve-opening degree. Internal sealing-surfaces produce minimal friction during open-close cycles, improving component service-life.
Important note: This globe-type stop-valve has definite flow-direction requirement. Medium must follow arrow marking on valve-body; reverse installation will damage sealing performance. Recommended to be installed by qualified plumbing technicians.
Core Technical Advantages
-
Short Working-Stroke Structure
Short valve-stem travel for opening-closing action, shortens operation cycle, lowers total travel distance of moving internal parts, reduces mechanical wear.
-
Minimized Friction Between Sealing Surfaces
Disc-seat contact friction is reduced during open-close stroke. Less abrasion for sealing mating-surfaces, extending valve service-life.
-
Visible Stem-Lifting Position Indication
Exposed rising stem clearly shows lifting height. Installers can directly judge real-time opening-degree without additional measuring instruments.
-
Reliable Sealing Performance
Stem mechanical pressing force forces disc tightly against valve-seat, achieving tight shut-off under rated working-pressure, suitable for both low-pressure and medium-high-pressure working-conditions.
-
Good Corrosion & Wear Resistance
High-quality forged-brass body plus matched internal trim materials, resist erosion from hot-water circulating-medium in heating-system pipelines.
-
Convenient Manufacturability & On-Site Maintainability
Reasonable Y-type body layout facilitates factory production and on-site disassembly inspection for installers and maintenance-contractors.
Specifications
|
Feature |
Description |
|
Place of origin |
China |
|
Brand name |
Yuanlun |
|
Product Name |
Internal-Thread German-Type Y-type Stop Valve |
|
Body Material |
Forged brass (to confirm alloy grade) |
|
Internal Trim |
Brass disc & seat assembly |
|
Thread Standard |
BSP internal-thread as standard; NPT available upon special request |
|
Nominal Pressure |
PN16 (1.6 MPa) |
|
Working Temperature |
5℃ ~ 90℃ |
|
Applicable Medium |
Cold-hot water, glycol-mixed heating-fluid, other non-corrosive liquids |
|
Operation Mode |
Manual hand-wheel rising-stem operation |
|
Size |
DN15-DN50 |
|
Minimum Order Quantity |
1 |
|
Price |
Negotiable |
|
Packing |
Yuanlun standard packing |
|
Payment Terms |
L/C, D/A, D/P, T/T, Western Union, MoneyGram |
|
Delivery Time |
15 Days |
How the Y-Pattern Stop Valve Works
-
Main Components & Function
|
Component |
Core Function |
|
Hand-wheel |
Manual rotation input for opening-closing operation |
|
Rising stem |
Converts rotary motion into linear lifting / descending displacement |
|
Disc (valve-clack) |
Moves up-down together with stem, mates with seat for sealing |
|
Valve seat |
Fixed sealing surface inside valve-body |
|
Y-angle flow-passage |
45° inclined channel for reducing fluid resistance |
-
Operating Principle
- Opening process: Rotate hand-wheel counter-clockwise. Stem lifts upwards, disc departs from valve-seat. Medium flows through Y-shaped inclined passage. Stem rising height reflects opening magnitude.
- Throttling process: Partial-stroke position of stem realizes intermediate throttling status for flow-rate adjustment.
- Closing process: Rotate hand-wheel clockwise. Stem pushes disc downward, pressing disc sealing-surface tightly onto seat, cutting off medium flow.
Critical installation reminder: Valve has unidirectional-flow requirement, follow casting-arrow direction on valve-body. Incorrect flow-direction assembly will cause sealing-failure and accelerated wear.
Application Scenarios
-
Residential & Commercial HVAC Heating Systems
Use-case: Branch-loop shut-off and throttling adjustment for radiator and floor-heating pipelines. Project value: Low-pressure-drop Y-passage reduces circulating-pump load; visible stem-position assists commissioning technicians for hydraulic balancing.
-
Domestic & Building Plumbing Piping
Use-case: Isolation and flow-regulation for cold-hot-water supply branch-pipelines. Project value: Reliable globe-valve throttling performance, convenient on-site maintenance.
-
Solar Thermal Circulating-Loops
Use-case: Shut-off & flow-control for solar-collector hot-water circulation pipelines. Project value: Adapt to temperature fluctuation of solar heating-medium, short-stroke operation for frequent switching occasions.
-
Light-Industrial Non-Corrosive-Fluid Circuits
Use-case: Process-water circulation, workshop auxiliary fluid-supply pipelines. Project value: Adapt medium-pressure working-conditions; good wear-resistance for long-term cyclic operation.
-
Water-Treatment Auxiliary Pipelines
Use-case: Shut-off and throttling for water-treatment equipment front-end branch-lines. Project value: Visible-stem opening-degree brings convenience for system debugging.
Installation Guide
-
Pre-Installation Check
- Confirm valve nominal-pressure, temperature rating match on-site working-condition.
- Identify flow-direction arrow cast on valve-body; strictly follow medium flow-orientation.
- Clean pipeline interior, remove welding-slag, sand and debris before valve mounting.
- Verify thread-specification consistency between valve and mating pipe-fittings.
-
Installation Steps
- Wrap PTFE sealing-tape for 3-5 clockwise circles on male-thread mating-port.
- Screw valve onto pipeline; wrench shall act on valve-body flats, do not apply torque onto hand-wheel.
- Guarantee valve-body arrow aligns with actual medium-flow-direction.
- Complete pipeline assembly, slowly pressurize system and execute joint-leakage inspection.
-
Important Installation Notes
- Installation recommended for qualified plumbing technicians.
- Strictly follow flow-direction marking; reverse-mounting will damage sealing performance.
- Do not over-tighten threaded joints, avoid brass-body thread cracking.
- Keep sufficient upper-space for full stem-lifting travel, prevent mechanical interference.
Maintenance & Troubleshooting
|
Phenomenon |
Probable Root-Cause |
Recommended Solution |
|
Valve cannot achieve tight shut-off |
Foreign-particle debris trapped between disc-seat sealing-surfaces; sealing-surface scratch damage |
Disassemble and clean internal cavity; repair or replace internal trim when sealing-surface is scratched |
|
Stem packing position leaks |
Packing gasket ageing; packing-gland insufficient compression |
Tighten packing-gland nut moderately; replace packing components when ageing |
|
Hand-wheel rotation feels stiff |
Stem-thread lack-lubrication; dirt & scale accumulated on moving-parts |
Clean internal components; apply compatible lubricant for stem thread |
|
Stem-lifting indication fails |
Internal transmission-structure jammed |
Disassemble inspection, eliminate foreign-object blockage |
Routine-Maintenance Suggestion
- Visual inspection for joint & packing leakage: Quarterly
- Hand-wheel open-close functional test: Annually
- Clean internal cavity if medium contains sediment: As-required
FAQ
Q: Can Y-type stop-valve be installed horizontally / vertically arbitrarily?
A: Valve-body can be mounted horizontal or vertical, but must guarantee medium flows following casting-arrow direction; meanwhile reserve enough space for full stem lifting-stroke.
Q: Can this valve be applied for steam-medium?
A: Not designed for steam-service. Suitable for liquid-phase cold-hot-water and non-corrosive-liquid within 5-90℃.
Q: Can I replace packing gaskets on-site without removing whole valve out of pipeline?
A: Isolate upstream-and-downstream pipeline pressure first; packing-gland can be operated on-site for packing adjustment or replacement.
Products Summary
Yuanlun German-type internal-thread Y-pattern stop-valve features 45° inclined Y-shaped flow-passage, short-stroke manual-rising-stem operation and visible stem-lifting position indication. DN15-DN50 size-range, PN16 pressure-rating. It delivers shut-off and throttling-control function for HVAC heating, building plumbing, solar thermal and light-industrial non-corrosive-fluid piping-systems. Sample-order supported for pre-project-evaluation, 15-day standard lead-time for worldwide plumbing-HVAC distributors and engineering-contractors.
Factory Information
Zhejiang Yuanlun Valve Co., Ltd. was founded in 2006, formerly known as Yuhuan Guohong Valve Co., Ltd. It is located in Yuhuan, Zhejiang Province, known as the "Valve Capital of China". After nearly two decades of stable development, Yuanlun Valve is a professional manufacturer for HVAC valves integrating R&D, production and sales. Our product portfolio covers floor heating systems, air-conditioning systems, domestic water valves, including ball valves, thermostatic valves, manifolds, check valves, stop valves, filter valves, angle valves, pipe fittings, corrugated pipes and other series.
Hot Tags: internal thread german type y-type stop valve, China internal thread german type y-type stop valve manufacturers, suppliers, factory, y-type stop valve

