MF Angle Brass Ball Valve

MF Angle Brass Ball Valve

Details
Place of origin: China
Brand name: Yunnl
Product Name:MF angle brass ball valve
Size: DN15-DN32
Minimum Order Quantity :1
Price: Negotiable
Packing:Yunnl standard packing
Payment Terms: L/C, D/A, D/P, T/T, Western Union,MoneyGram
Delivery Time:15 Days
Applicable temperature: 5℃ to 90℃
Category
Angle Brass Ball Valve
 
Send Inquiry
Description
Technical Parameters

MF Angle Brass Ball Valve

 

Three Connection Methods for Angle Valves

Not every angle valve needs a union connection. The choice depends on how often the valve will be serviced and how much space is available for maintenance.

Connection Method Disassembly Time Pipe Disturbance Best For
Standard Threaded 30 minutes Both ends Never-service installations
Union (This Product) 5 minutes One end only Periodic maintenance, tight spaces
Quick-Connect 10 seconds None Temporary systems, frequent changes

This product is the union type - it sits between the two extremes: faster than threaded, more permanent than quick-connect.

 

When to Choose Union Over Threaded

  • Choose Union When…

Situation Why Union Helps
Valve is behind a toilet No space for two wrenches on threaded connections
Under-sink cabinet installation Can't rotate pipes; union nut works in place
Radiator inlet with finished wall Don't want to break wall-pipe thread seal
Rental property maintenance Fast valve replacement between tenants
Multi-unit building Standardized service procedure for all units
Appliance isolation point Periodic appliance replacement without re-plumbing
  • Choose Standard Threaded When…

Situation Why Threaded Is Sufficient
New construction, never-serviced location Lower cost, no maintenance expected
Accessible pipe with room for wrenches Easy to break both connections
Temporary installation Will be removed entirely
Below-grade or concealed installation Service access not planned

 

Product Overview

Yunnl MF angle ball valve is a 90° shut-off valve with a male/female union joint on one end. The union allows the valve body to be separated from the pipeline without rotating or disturbing the fixed pipe connection on the opposite end.

Two ends, two connection types:

End Connection Purpose
Bottom Female thread (BSP/NPT) Connects to wall pipe
Side Male/Female union nut Connects to fixture supply

The union end is where disassembly happens - the wall-pipe connection stays permanently sealed.

 

Core Technical Advantages

  • One-Side Maintenance Access

The union joint allows valve service without disturbing the wall-pipe connection. This is the primary advantage over standard threaded angle valves.

  • 90° Angle Body - No Extra Elbow

The valve body integrates the 90° turn. No separate elbow fitting is required between the wall pipe and the fixture supply.

  • PTFE Seats - Zero-Leakage Shut-Off

PTFE seats provide Class A (zero-leakage) shut-off in the closed position. Self-adjusting design compensates for wear over the valve's service life.

  • Forged Brass Body - No Internal Porosity

The valve body is hot-forged, not cast. No internal voids, higher tensile strength, reliable pressure containment under PN16 rating.

  • Chrome-Plated Ball - Smooth Operation

The brass ball core is chrome-plated for corrosion resistance and low friction during rotation. Handle operation remains smooth over thousands of cycles.

  • Handle Position Visual Indication

Handle parallel to pipe = open. Handle perpendicular to pipe = closed. Visual confirmation without operating the valve.

 

1501

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Specifications
Feature Description

Place of origin

China

Brand name

Yunnl

Product Name

MF Angle Brass Ball Valve
Body Material Forged Brass
Seat Material PTFE
Seal Material EPDM O‑rings
Union Connection Male/Female union nut (one end)
Other End Female thread (BSP/NPT)
Nominal Pressure PN16 (1.6 MPa)
Working Temperature 5°C ~ 90°C
Operation 90° lever handle
Applicable Medium Cold water, hot water, heating water, non‑corrosive fluids

Size

DN15-DN50

Minimum Order Quantity

1

Price

Negotiable

Packing

Yunnl standard packing

Payment Terms

L/C, D/A, D/P, T/T, Western Union,MoneyGram

Delivery Time

15 Days

 

 

 

MF Union Connection: How It Works

A union assembly is built from three separate parts to enable quick valve disconnection: Union nut (female threaded) – Hexagonal oversized nut which fastens onto the male thread of piping or adaptors. Tightening this nut applies compression to form the union seal. Union hub (male thread integrated on valve body) – Male threaded section machined directly into the valve body to engage with the union nut. An O-ring or flat gasket is fitted at the joint interface for sealing. Precision sealing surface – A finely machined contact face on the valve unit. It aligns against the piping/adaptor end, relying on the O-ring to achieve a bubble-tight seal.

Installation Steps

  1. Slide and screw the union nut onto the male pipe thread
  2. Position the valve body inside the union nut
  3. Tighten the nut by hand first, then apply an additional 1/4 wrench turn
  4. Compression acts on the O-ring sandwiched between valve body and pipe end to form a watertight joint

Disassembly Steps for Maintenance

  1. Shut the valve, rotating the handle perpendicular to the pipeline
  2. Use a wrench to unscrew the union nut in counter-clockwise direction
  3. Draw the valve body out from the piping; the fixed pipe thread stays untouched throughout this process
  4. Carry out valve servicing: internal cleaning, seat renewal or O-ring replacement
  5. Fit the valve back in place and re-torque the union nut

Core benefit: The piping joint on the opposite fixture side remains fully intact. Only the union joint is opened and re-sealed for inspection or repair work.

 

Application Scenarios

  • Toilet & Bathroom Fixture Isolation

Installed at the wall outlet behind toilets, the MF angle valve allows quick shut-off for toilet repairs. The union connection makes it easy to replace the valve itself if it fails - no need to disturb the wall pipe threading.

  • Kitchen & Vanity Sink Supplies

Under-sink installations benefit from the union connection - servicing the valve does not require disconnecting the supply hose from the fixture. This is particularly valuable when replacing a worn valve in a tight under-sink cabinet.

  • Washing Machine & Laundry Connections

The union connection allows the valve to be replaced without disturbing the laundry wall box plumbing. This simplifies maintenance in multi-unit residential buildings.

  • Heating Radiator Supply Lines

On radiator inlet connections, the MF angle valve provides both flow control and easy maintenance access. The union allows radiator removal without draining the entire heating system.

  • Appliance Isolation (Water Heaters, Dishwashers)

Any appliance requiring periodic service benefits from the union connection - isolate the appliance, service it, and reconnect without disturbing the main plumbing.

  • Light-Commercial Plumbing

Office buildings, retail spaces, and multi-family housing benefit from the reduced maintenance time and simplified service access of union-connected angle valves.

 

Installation & Maintenance Guide

  • Installation

  1. Verify thread type - Confirm BSP or NPT on both pipe ends
  2. Clean threads - Remove dirt, old tape, or debris from pipe threads
  3. Apply thread tape - On the threaded end (non-union side), apply PTFE tape (3-5 wraps clockwise)
  4. Thread the valve - Thread the valve onto the pipe by hand, then tighten with a wrench using the body flats
  5. Connect the union side - Thread the union nut onto the other pipe end. Do not tighten fully yet
  6. Position the valve - Orient the valve body so the handle operates freely
  7. Tighten the union nut - Hand-tighten, then 1/4 turn with a wrench
  8. Check operation - Rotate the handle through full open and closed positions
  • Maintenance (Union Disassembly)

  1. Close the valve - Rotate handle to closed position
  2. Loosen the union nut - Use a wrench to loosen the union nut on the union side
  3. Remove the valve body - Pull the valve away from the pipe
  4. Inspect/replace seats - Check PTFE seats for wear; replace if damaged
  5. Inspect/replace O-ring - Check the union O-ring; replace if cracked or flattened
  6. Reassemble - Insert the valve body, tighten the union nut, and reopen the valve
  7. Test for leakage - Pressurize and check both connections
  • Torque Guidelines

Size Union Nut Torque (N·m) Threaded End Torque (N·m)
DN15 15-25 15-20
DN20 20-30 20-30
DN25 30-45 30-40
DN32-DN50 40-60 40-60

 

Building Type Selection Guide

Different building types have different maintenance expectations and space constraints. Here is how to specify the right angle valve for each.

Building Type Typical Valve Location Recommended Valve Reason
Single-family house Toilet, sink, laundry Union Tight spaces, DIY maintenance
Apartment building Every unit Union (standardized) Reduce per-unit maintenance time
Luxury hotel Guest rooms Union Fast room turnaround between guests
Hospital patient rooms Behind toilets Union Frequent disinfection and inspection
School restrooms Public facilities Union High-frequency service
Office building Private restrooms Union Standardized maintenance procedure
Retail store Public restrooms Union Variable maintenance access
Factory utility room Equipment isolation Standard threaded Exposed pipe, easy access
Warehouse Utility sink Standard threaded Maintenance access available

 

Maintenance Cost Quantification: 5-Year and 10-Year Analysis

For a typical apartment building with 50 toilet isolation valves, here is the maintenance cost comparison over 5 and 10 years.

Assumptions:

  • Labor rate: $60/hour
  • Standard threaded valve service: 30 minutes
  • Union angle valve service: 5 minutes
  • Service frequency: 1 event per valve per 5 years (conservative)
Cost Factor Standard Threaded Union (This Product)
Service time per valve 30 minutes 5 minutes
Labor cost per service $30 $5
5-year service events (50 valves) 50 events 50 events
5-year labor cost $1,500 $250
10-year service events 100 events 100 events
10-year labor cost $3,000 $500
Pipe sealant/tape $50 $10
10-year total cost $3,050 $510
Savings with union valve - $2,540 (83%)

Not included: reduced downtime, avoided pipe damage, emergency service premium.

Conclusion: The union valve's higher initial cost is recovered within the first service event. Over 10 years, the savings exceed $2,500 per building.

 

FAQ

Q: What does "MF" mean in MF angle brass ball valve?

A: "MF" stands for Male/Female union connection. One end of the valve has a union nut that allows the valve body to be separated from the pipe without disturbing the threaded joint on the other end.

Q: What is the advantage of the MF union design?

A: The union allows for easy valve removal and maintenance without disturbing the pipe connections. This reduces maintenance time from approximately 30 minutes to about 5 minutes.

Q: What is the difference between this valve and a standard angle valve?

A: A standard angle valve has threaded connections on both ends. The MF angle valve has a union connection on one end, allowing tool-free disassembly for maintenance.

Q: What is the pressure rating?

A: PN16 (1.6 MPa / 16 bar). Higher pressure ratings available on request.

Q: What is the temperature range?

A: 5°C to 90°C with EPDM seals.

Q: What thread standards are available?

A: BSP is standard. NPT is available on request.

Q: Can this valve be used for gas?

A: Yes, for non-corrosive gas applications up to PN16. Specify gas service when ordering for appropriate seal selection.

Q: Is the union O-ring replaceable?

A: Yes. The O-ring is a serviceable component. Replacement O-rings are available.

Q: Is horizontal or vertical installation supported?

A: Yes. The angle valve can be installed in any orientation, though the handle should be accessible for operation.

Q: Are samples available?

A: Yes, MOQ is 1 unit. Sample orders are supported for quality and dimension verification.

 

Ordering Information

For plumbing distributors, HVAC contractors, facility managers and project purchasers:

  • Sample order: 1 unit minimum for quality and thread verification
  • Bulk orders: Volume pricing, flexible payment terms
  • Custom options: Thread type (BSP/NPT), seal material (EPDM/FKM), pressure rating (PN16/PN25/PN40), custom marking
  • Lead time: 15 working days after deposit
  • Packing: Standard export cartons
  • Payment: L/C, T/T, D/A, D/P, Western Union, MoneyGram

 

Quality Assurance

  • 100% factory pressure‑tested – each valve tested at 1.1× rated pressure
  • 100% seat leakage test – zero leakage in closed position under test pressure
  • Thread gauge inspection – all connections verified to BSP/NPT standard
  • Union nut torque check – each union tested for smooth operation
  • Material certification – spectrographic analysis available
  • ISO 9001 certified manufacturing facility

 

Closing Summary

Yunnl MF union angle ball valve provides serviceable 90° shut-off for fixture isolation. The MF (Male/Female) union allows the valve body to be separated from the pipeline without disturbing threaded pipe joints - reducing maintenance time from 30 minutes to 5 minutes. Forged brass body, chrome-plated ball, PTFE seats, EPDM seals, PN16 rating, 5-90°C. Available DN15-DN50 with BSP or NPT threads. Suitable for toilet, vanity, washing machine, radiator and appliance isolation where easy maintenance access is required. Sample support, 15-day delivery and flexible payment terms.

 

Factory Information

product-600-354
product-600-354
product-600-354
product-600-354

Zhejiang Yuanlun Valve Co., Ltd. was founded in 2006, formerly known as Yuhuan Guohong Valve Co., Ltd. It is located in Yuhuan, Zhejiang Province, on the coast of the East China Sea, which is renowned as the "Valve Capital". After nearly two decades of continuous and stable development, Yuanlun Valve has become a professional manufacturer of HVAC valves integrating design and development, production and processing, and sales and trade, as well as a modern enterprise with scientific management.

The company's products cover floor heating systems, air conditioning systems, domestic water valve systems, etc. For instance, there are ball valves, thermostatic valves, manifolds, check valves, stop valves, gate valves, filter valves, angle valves, faucets, pipe fittings, corrugated pipes, H valves and other series.

 

 

Hot Tags: mf angle brass ball valve, China mf angle brass ball valve manufacturers, suppliers, factory, FF Angle Brass Ball Valve, Brass ball valve MM angle connection type, MF Angle Brass Ball Valve, FxF threaded brass ball valve, brass angle ball valve

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!