External Thread Direct 20*25

External Thread Direct 20*25

Details
Yunnl H59 brass 20×25 double male thread reducing adapter, cross diameter transition fitting for 20mm & 25mm pipelines. High temperature & corrosion resistant, tight thread sealing, easy screw installation, widely used in building water supply and underfloor heating systems. Low MOQ 1 unit, 15-day delivery, global trade payment terms supported.
Category
PEX Pipe Fittings
 
Send Inquiry
Description
Technical Parameters

External Thread Direct 20*25

 

 

The Diameter Mismatch Problem

Every plumbing project faces the same challenge: pipes and equipment come in different sizes.

  • A 20mm pipe needs to connect to a 25mm valve
  • A 15mm branch splits from a 25mm main
  • A water heater has 20mm ports, but the house supply is 25mm

The solution: A reducing nipple. One end matches the smaller pipe; the other end matches the larger fitting. No adapters, no extra joints, no complications.

The challenge: Some installers use multiple fittings to bridge the gap-a coupling plus a reducer plus another coupling. More components = more connections = more leak points.

The better solution: One fitting does the job. The Yunnl brass reducing nipple has two different-sized male threads on a single forged body.

Multiple Fittings One Reducing Nipple (This Product)
3+ components 1 component
4+ threaded joints 2 threaded joints
More leak points Fewer leak points
More installation time Faster installation
Higher cost Lower cost

 

Product Overview

Yunnl brass reducing nipple is a male‑to‑male threaded reducer designed to connect two different diameter female threaded ports. One end features a 20mm male thread; the other end features a 25mm male thread. The fitting allows quick diameter conversion between 20mm and 25mm pipelines without additional adapters.

The fitting is forged from H59 brass with a precision‑machined thread on both ends. An integrated retaining flange prevents over‑tightening and protects the thread from damage.

 

Size Reference: 20mm and 25mm in Context

This Product DN (Nominal Diameter) Inch Reference Typical Use
20mm end DN15 1/2″ Small branches, fixtures
25mm end DN20 3/4″ Main branches, equipment

This reducing nipple connects:

  • 20mm (DN15) pipes to 25mm (DN20) fittings
  • 1/2″ threaded equipment to 3/4″ pipe lines
  • Small branch lines to larger mains

Note: Thread sizes refer to the pipe thread size, not the actual thread outer diameter. A 20mm male thread mates with a 20mm (DN15) female threaded port.

 

Core Performance Advantages

  • Forged H59 Brass Construction

The fitting is forged, not cast:

  1. Dense, void‑free grain structure
  2. Higher tensile strength
  3. Corrosion resistance for water systems
  4. No internal porosity (unlike cast)
  • Precision‑Machined Threads

CNC‑rolled external threads provide:

  1. Uniform tooth pitch
  2. Smooth engagement with female threads
  3. Consistent sealing with PTFE tape
  4. Reduced risk of cross‑threading
  • Dual Male Threads – One‑Piece Design

Both ends are male threads on a single forged body:

  1. No welded seams
  2. No assembly required
  3. Maximum strength
  • Integrated Retaining Flange

The middle flange prevents:

  1. Over‑tightening during installation
  2. Thread damage from excessive insertion
  3. Misalignment during assembly
  • Wide Temperature Range

5°C to 90°C covers:

  1. Cold water supply
  2. Domestic hot water
  3. Floor heating circuits
  4. HVAC systems
  • PN16 Pressure Rating

Rated to 1.6 MPa (16 bar), tested to 1.76 MPa:

  1. Suitable for standard water and heating systems
  2. Safety margin for pressure fluctuations

 

12

 

Specifications

Feature Description

Place of origin

China

Brand name

Yunnl

Product Name

External Thread Direct 20*25

Size

20*25
Main Raw Material Brass
Working Temperature 5°C ~ 90°C
Nominal Working Pressure PN16 / 1.6MPa
Test Sealing Pressure 1.76MPaLeakage-Free Test
Application Medium Cold tap water, domestic hot water, floor heating circulating water

Minimum Order Quantity

1

Price

Negotiable

Packing

Yunnl standard packing

Payment Terms

L/C, D/A, D/P, T/T, Western Union,MoneyGram

Delivery Time

15 Days

 

Main Application Scenarios

  • Building Cold & Hot Water Supply

Use case: Connecting 20mm branch lines to 25mm main supply pipes.
Installation: 20mm end connects to the branch line; 25mm end connects to the main pipe fitting.
Value: Simple diameter transition without extra adapters.

  • Water Heater Connections

Use case: Connecting 25mm building supply to a 20mm water heater inlet.
Installation: 25mm end to the supply; 20mm end to the heater.
Value: Eliminates need for a separate reducer + coupling.

  • Floor Heating Manifolds

Use case: Connecting 20mm floor heating loops to 25mm manifold branches.
Installation: 20mm end to the floor loop; 25mm end to the manifold.
Value: Compact transition in tight manifold cabinets.

  • Central Air Conditioning Water Circuits

Use case: Connecting 20mm fan coil unit pipes to 25mm main supply/return.
Installation: 20mm end to the FCU; 25mm end to the main line.
Value: Reliable transition in HVAC systems.

  • Fixture Branch Connections

Use case: Connecting 20mm fixture supply lines to 25mm risers.
Installation: 20mm end to the fixture; 25mm end to the riser.
Value: Simple, clean installation behind walls.

  • Pump & Equipment Connections

Use case: Connecting different-sized threaded ports on pumps and equipment.
Installation: Match each end to the corresponding port size.
Value: One fitting solves the size mismatch.

 

Installation Guide

  • Pre‑Installation Preparation

  1. Clean both pipe threads – Remove rust, dirt, old tape, and debris
  2. Check thread condition – Ensure threads are not damaged
  3. Confirm size matching – 20mm end to 20mm female; 25mm end to 25mm female
  • Installation Steps

  1. Apply PTFE tape – Wrap 3‑5 turns clockwise on the 20mm male thread
  2. Thread into the smaller port – Hand‑tighten, then 1/4 turn with a wrench
  3. Apply PTFE tape – Wrap 3‑5 turns clockwise on the 25mm male thread
  4. Thread into the larger port – Hand‑tighten, then 1/4 turn with a wrench
  5. Final tightening – Use a wrench on the retaining flange
  • Torque Guidelines

End Recommended Torque (N·m)
20mm (DN15) 15‑25
25mm (DN20) 20‑30
  • Important Notes

  1. Do not over‑tighten – Brass threads can crack
  2. Use PTFE tape only – Do not use liquid sealant on male threads (it can enter the system)
  3. Hold the flange – Use the retaining flange as a wrench point
  4. Check alignment – Ensure the fitting is straight after tightening

 

Material & Sealing Details

  • Thread Standards

Standard Thread Angle Typical Use
BSP / G 55° parallel European and international plumbing
NPT 60° tapered North American plumbing

This fitting is available in both standards. Specify your requirement when ordering.

  • Sealant Options

Sealant Best For Application
PTFE tape General water and heating 3‑5 wraps clockwise
Thread sealant High vibration, high pressure Apply to male thread
None O‑ring sealed joints Not applicable for this product
  • Testing

After installation:

  1. Pressurize the system to working pressure
  2. Check both threaded joints for leakage
  3. If leakage occurs, tighten slightly or re‑apply tape

 

Brand Strength & Quality Assurance

  • Yunnl Factory Advantages

Yunnl Valve specializes in brass plumbing fittings for decades. All brass nipples pass strict pressure and aging tests before delivery. We support sample orders, bulk engineering wholesale and customized special thread sizes.

  • Quality Control

Every batch of male thread reducers undergoes air tightness leakage test, raw material composition inspection and dimensional calibration to meet international plumbing standards.

 

FQA

Q: What is a double external thread brass reducer nipple used for?

A: It is a reducing transition fitting with male threads on both ends, used to connect 20mm and 25mm female thread pipes, realize pipeline diameter conversion for domestic water and floor heating systems.

Q: Can this 20×25 male thread nipple resist high temperature floor heating water?

A: Stable under 95°C hot circulating water, no deformation or aging for long-term floor heating operation.

Q: Can I order a small sample quantity for testing?

A: MOQ is only 1 unit, we support small sample orders for distributors and engineering contractors.

 

Product Closing Summary

Yunnl 20×25 H59 brass double male external thread reducer nipple is a practical reducing pipe adapter for global plumbing and underfloor heating projects. Featuring PN16 pressure resistance, 5°C~95°C wide temperature range, precise leak-proof thread and easy screw installation, it solves diameter matching problems between 20mm and 25mm pipelines. Flexible sample orders, 15-day fast delivery and multiple global payment methods help plumbing distributors, renovation contractors and construction project buyers cut procurement and construction costs.

 

Hot Tags: external thread direct 20*25, China external thread direct 20*25 manufacturers, suppliers, factory, Male Thread Elbow 20*2.0PEX Pipe Fittings, Male-to-male PEX fitting, 20*25 male threaded straight fitting, External*external Thread Pex Pipe Fittings, pex pipe fittings, 20*2.0 PEX External Thread Elbow Fittings

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!