Ball Core Angle Valve
Angle vs. Straight: Which Valve Fits Your Layout?
In wall-outlet fixture connections, space constraints require a 90° directional change without additional pipe fittings. Standard straight valves need an extra elbow, adding two threaded joints and potential leak points. Angle valves integrate the 90° turn within the valve body.
Straight-through valves: Require pipes keep same axis. If wall-outlet pipe needs immediate 90° turn toward fixture, extra elbow fitting is required, bringing extra cost, more joints and higher leakage risk.
Angle valves: Integrate 90-degree turning inside valve body. Medium flows in from wall inlet and exits at right angle toward fixture directly. No extra elbow needed, fewer joints for cleaner installation.
Yuanlun brass ball core angle valve combines shut-off function and flow direction change within one compact component.
| Feature | Straight Valve + Elbow | Angle Ball Valve (This Model) |
|---|---|---|
| Fittings required | 2 (valve + elbow) | 1 |
| Threaded joints | 4 | 2 |
| Potential leak points | 4 | 2 |
| Installation space | Extended | Compact |
| Flow direction | Straight through | 90° turn (integrated) |
Product Overview
Angle valves are durable plumbing fittings mostly constructed from brass or stainless-steel, stable under pressure, temperature and slightly corrosive environment.
There are two mainstream quick-opening angle-valve types in our product portfolio:
- Ball core angle valve: The quick-opening ball core angle valve adopts ball-core structure. It delivers full-bore passage under fully-open status, featuring outstanding high-flow performance. It is preferred for projects requiring large water throughput.
- Slow-opening fine-polished angle valve (ceramic cartridge type): Equipped with slow-open ceramic cartridge. Handle needs 360° rotation to complete opening or closing stroke. It realizes gentle flow adjustment, suitable for working conditions demanding precise flow throttling.
This Yuanlun brass ball-core angle stop valve is quarter-turn shut-off fitting for confined plumbing space. Built-in 90-degree body turns fluid direction from wall outlet to terminal fixture without separate elbow component.
It uses chrome-plated brass ball core; only 90° rotation realizes full-open / full-close. Lever-handle gives visible running status: handle parallel to flow direction = open; perpendicular = closed.
Hot-forged brass body with multi-layer chrome plating resists tarnish and bathroom condensation. PTFE valve seats plus EPDM O-rings achieve bubble-tight shut-off under rated working pressure.
Core Technical Advantages
-
Full-bore flow path
Ball core design provides full-bore passage when fully open. Suitable for high-flow fixture supply.
-
Strong durability
Made from high-quality forged brass material, the valve features excellent pressure resistance and explosion-proof performance, capable of withstanding fluctuating water hammer pressure and ensuring long-term service life.
-
90° quarter-turn operation
Single-hand operation for rapid isolation. Handle position provides visual confirmation of valve status.
-
Corrosion-resistant finish
Multi-layer electroplating maintains surface integrity under humid conditions.


| Feature | Description |
|
Place of origin |
China |
|
Brand name |
Yunnl |
|
Product Name |
Ball Core Angle Valve |
| Body Material | Forged Brass |
| Surface Finish | Polished Chrome‑Plated / Nickel‑Plated |
| Seat Material | PTFE |
| Seal Material | EPDM O‑rings |
| Thread Standard | BSP (standard), NPT (on request) |
| Nominal Pressure | PN16 (1.6 MPa) |
| Working Temperature | 5°C ~ 90°C |
| Operation | Quarter‑turn (90°) lever handle |
| Applicable Medium | Cold water, hot water, non‑corrosive fluids |
|
Size |
DN15-DN50 |
|
Minimum Order Quantity |
1 |
|
Price |
Negotiable |
|
Packing |
Yunnl standard packing |
|
Payment Terms |
L/C, D/A, D/P, T/T, Western Union,MoneyGram |
|
Delivery Time |
15 Days |
How the Quarter‑Turn Ball Valve Works
Polished brass ball core with central bore is the core component, assembled between two PTFE seats inside valve body. Stem links ball core to external lever handle.
- OPEN: Handle parallel to pipe. Ball bore aligns with pipeline axis; medium flows through with low pressure drop.
- CLOSED: Handle rotated 90° perpendicular to pipe. Solid wall of ball blocks flow path; compressed PTFE seats achieve bubble-tight sealing.
Built-in limit stops on valve body prevent over-rotation and fix full-open / full-closed positions. Most versions adopt full-port ball bore for minimum pressure loss.
Operation note: This valve is designed for on-off service only (full open / full closed). Do NOT use for throttling. Long-term partial opening will abrade PTFE seats and shorten sealing lifespan.
Installation Guide
-
Pre-Installation
- Confirm thread standard: BSP default, NPT available upon request.
- Check flow direction: bottom port = inlet (wall pipe); side port = outlet (to fixture).
- Inspect valve condition; rotate handle to confirm smooth movement.
-
Installation Steps
- Prepare wall pipe: clean male thread, remove old sealant & debris. Wrap PTFE tape clockwise for 3-5 rounds.
- Hand-thread valve onto wall pipe bottom port. Adjust orientation to make side outlet point toward fixture. Tighten on valve body flats with wrench; never apply torque on handle; avoid over-tightening to prevent brass thread crack.
- Connect flexible supply hose or rigid pipe to side outlet. Use built-in washer/O-ring for sealing; PTFE tape is not required if washer is fitted.
- Tighten supply-line nut, slowly open valve, inspect all threaded joints for leakage.
- Cycle handle open-closed several times for function test. Adjust orientation if needed. Keep handle accessible after installation.
Application Scenarios
-
Toilet / WC supply lines: Quick shut-off for toilet tank maintenance & flapper replacement.
-
Vanity & sink faucet cold-hot water supply.
-
Washing-machine & laundry room water supply isolation.
-
Kitchen sink & dishwasher under-cabinet water supply.
-
Appliance isolation: water heater, filtration unit, ice maker. Isolates individual equipment without building-wide water shutdown.
FAQ
Q: What is the difference between an angle ball valve and a straight ball valve?
A: An angle ball valve has a 90° body configuration-inlet and outlet are perpendicular. A straight ball valve has inlet and outlet on the same axis. Choose angle when the water supply comes from the wall and needs to turn immediately to the fixture; choose straight when the pipe continues in the same direction.
Q: Can this valve be used for hot water?
A: Yes. The working temperature range is 5°C to 90°C, covering standard domestic hot water (typically 40‑60°C) and heating water applications.
Q: What is the pressure rating?
A: PN16 (1.6 MPa / 16 bar) at ambient temperature. Standard residential and commercial water pressure (0.2‑0.6 MPa) is well within the valve's rating.
Q: Can this valve be used for throttling flow?
A: Not recommended. Ball valves are designed for full open / full closed service. Partial opening can cause erosion of the PTFE seats and reduce sealing life.
Q: What thread standard do you use?
A: Standard is BSP (British Standard Pipe). NPT (National Pipe Taper) is available on request. Please specify when ordering.
Q: How is valve position indicated?
A: Handle position provides visual indication: handle parallel to the pipe outlet = open; handle perpendicular = closed.
Q: Is horizontal or vertical installation supported?
A: The angle valve is designed for wall‑mount installations with the inlet port (bottom) connected to the wall pipe and the outlet (side) pointing toward the fixture. It can be rotated to accommodate different wall pipe positions.
Q: What is the difference between the metal handle and blue plastic handle?
A: Both provide the same valve operation. Metal handles are often used in exposed installations for a premium finish; blue plastic handles are sometimes used for cold water identification (red for hot). Functional performance is identical.
Q: Is the handle removable?
A: Yes, on most models. The handle is secured by a hex nut on the stem and can be removed or repositioned 90° or 180° to suit installation orientation.
Q: Do you offer samples?
A: Yes. Minimum order quantity is 1 unit. We recommend ordering a sample to verify thread compatibility and dimensional fit.
Products Summary
Yunnl brass angle ball valve provides compact, reliable shut‑off control for plumbing fixtures where space is constrained and water must turn 90° from wall to fixture. The quarter‑turn operation, chrome‑plated forged brass body, PTFE seats and PN16 rating make it a specified for fixture isolation in residential and light-commercial plumbing. Available DN15‑DN50 with BSP or NPT threads, metal or plastic handle options. Sample support, 15‑day delivery and flexible payment terms available for global plumbing distributors and contractors.
Hot Tags: ball core angle valve, China ball core angle valve manufacturers, suppliers, factory, quick opening angle valve, Angle valve with ball core
