Double-adjustable Floor Heating Manifold
Two Ways to Balance a Heating System
Hydraulic balancing is a mandatory requirement for every hydronic underfloor heating installation. Without proper flow balancing, certain heating loops will overheat while other rooms remain cold, leading to inconsistent indoor temperature and wasted heating energy.
There are two mainstream balancing solutions for water floor heating systems:
- Flow meter manifolds: Each circuit is fitted with transparent flow meters. Heating technicians read real-time flow data and adjust valve opening accordingly. This solution delivers high balancing precision yet comes with a higher product cost.
- Double-regulating manifolds: Every heating circuit features regulating valves mounted on both supply bar and return bar. Installers tune the system based on room temperature feedback. This solution is cost-effective while maintaining reliable balancing performance.
This Yunnl manifold adopts the double-regulating design. It supports manual hydraulic balancing at a lower procurement cost compared to flow meter manifolds, making it the preferred option for budget-conscious residential and light-commercial heating projects where inline flow measurement is not required.
| Feature | Flow Meter Manifold | Double-Regulating Manifold (This Product) |
|---|---|---|
| Flow display | Yes, built-in flow meter | No |
| Balancing method | Adjust by reading flow meter values | Adjust based on room temperature feedback |
| Supply regulating valve | Yes | Yes |
| Return regulating valve | Yes | Yes |
| Product cost | Higher | Lower |
| Ideal application | High-precision hydraulic balancing | Standard balancing, cost-sensitive heating projects |
Introduction
Yunnl double-regulating manifold is a manual balancing manifold dedicated to hydronic underfloor radiant heating systems. The whole assembly consists of one supply manifold bar and one return manifold bar. Each heating circuit is equipped with independent regulating valves on both bars.
The definition of "double-regulating": every heating loop has an adjustment valve on the supply side and return side. This dual-valve architecture delivers finer flow control compared with single-valve manifolds. Heating contractors can perform system balancing by tuning valves on both sides independently.
This manifold covers 2 to 12 circuit specifications to match various project scales, ranging from compact studio apartments, family houses, large multi-floor villas, to light-commercial premises.
Full Set Components & Functions
A complete manifold assembly includes supply bar, return bar and matching accessories, with dedicated regulating components for each branch. Below lists all standard parts buyers receive within one full set.
| Component | Quantity | Core Function |
|---|---|---|
| Supply manifold bar | 1 | Distribute hot water to individual heating circuits; fitted with double regulating valves for manual flow adjustment |
| Return manifold bar | 1 | Collect cooled return water; valve seats compatible with thermal electric actuators for zone on/off control |
| Mounting brackets | 2 | Galvanized brackets for wall mounting inside manifold cabinet |
| Air vent valve | 1 | System air bleeding during commissioning |
| Drain valve | 1 | Flush and drain the heating system |
| End caps | 2 | Seal both ends of manifold bars |
Optional Accessories (Ordered Separately)
- Compression fittings for 16×2.0 mm /18×2.0 mm PEX & PE-RT underfloor heating pipes
- Thermal electric actuators, NO / NC types optional
- Extra galvanized mounting brackets
Component notes:
Supply manifold bar: Built-in double regulating valves for fine manual flow tuning on each heating branch. Each outlet controls the water volume delivered to floor heating pipes.
Return manifold bar: Pre-installed actuator-compatible valve seats. It accepts standard thermal electric actuators to enable remote zone control linked with room thermostats.
All branch outlets work with standard 16×2.0 mm and 18×2.0 mm PEX or PE-RT pipes using compression fittings. Installers can assemble or replace compression connectors on site according to local pipe specifications.
Material & Manufacturing Specifications
Material quality determines long-term reliability of floor heating hardware, which continuously works under circulating hot water and cyclic pressure all year round.
The manifold main bars are forged from high-grade brass, different from common cast brass alternatives. Forged construction eliminates internal porosity defects, improving pressure resistance under PN16 continuous working conditions. Multi-step electroplating and passivation treatment are applied to resist internal oxidation and scale buildup inside heating circulation loops.
Internal valve cores adopt tapered multi-layer sealing construction. Repeated opening and closing cycles will not easily damage sealing surfaces, minimizing hidden leakage risks for embedded underfloor piping systems. All rubber gaskets use high-temperature resistant EPDM compound, maintaining stable sealing performance under continuous hot water circulation.








| Feature | Description |
|
Place of origin |
China |
|
Brand name |
Yunnl |
|
Product Name |
Double-adjustable Floor Heating Manifold |
| Main Body Material | Forged brass, electroplated & passivated surface treatment |
| Sealing Material | High‑temperature EPDM rubber |
| Available Circuits | 2‑12 circuits |
| Nominal Pressure | PN16 (1.6 MPa) |
| Working Medium | Closed‑loop hot heating water |
| Working Temperature Range | 5℃ ~ 90℃ |
| Control Option | Manual flow balancing; compatible with standard thermal electric actuators |
|
Size |
DN25 |
|
Minimum Order Quantity |
1 |
|
Price |
Negotiable |
|
Packing |
Yunnl standard packing |
|
Payment Terms |
L/C, D/A, D/P, T/T, Western Union,MoneyGram |
|
Delivery Time |
15 Days |
Double-Regulating vs Single-Regulating Manifold
| Feature | Single-Regulating Manifold | Double-Regulating Manifold (This Product) |
|---|---|---|
| Valves per heating circuit | 1 valve, return side only | 2 valves, supply + return side |
| Flow control range | Limited adjustment range | Wider adjustable range |
| Hydraulic balancing precision | Moderate | Higher |
| Installation complexity | Simple installation | Slightly higher installation workload |
| Product cost | Lower | Slightly higher |
| Suitable projects | Simple small heating systems | Large multi-zone heating systems |
Benefits of Double-Regulating Structure
- Dual-side valve adjustment enables precise flow control for every individual heating circuit
- Delivers uniform temperature distribution across different rooms in one heating system
- Compensates pressure differential between short loops and long floor heating circuits
Working Principle of Double-Regulating Manifold
-
Hydraulic Balancing Workflow
- Hot water flows into the supply manifold bar from boiler / heat source
- Supply-side regulating valves adjust water inflow for each independent heating circuit
- Hot water circulates through embedded floor heating pipes to release heat
- Cooled water flows back into the return manifold bar
- Return-side regulating valves control outflow speed for each circuit
- Fully balanced return water flows back to the heat source
-
Function of Dual Valves
- Supply valve: Controls the volume of hot water entering each heating loop
- Return valve: Controls the return speed of circulated water
- Combined effect: Achieve precise fine-tuning of flow rate on every circuit
- With single regulating manifolds, adjusting one loop's valve will interfere with flow status of other circuits. With double-regulating design, each heating circuit can be hydraulically balanced independently.
Application Scenarios
- Small Apartments (2–4 Circuits)
Projects: Studio, one-bedroom or two-bedroom apartments
Configuration: 2–4 circuit manifold
Value: Compact and economical hydraulic balancing solution for small residential heating spaces
- Standard Family Houses (5–8 Circuits)
Projects: 3–5 bedroom houses with multiple heating zones
Configuration: 5–8 circuit manifold
Value: Zone-wise balancing to guarantee even heating across the whole building
- Large Villas (9–12 Circuits)
Projects: Multi-story large residences with multiple independent zones
Configuration: 9–12 circuits, multiple manifolds can be combined
Value: Independent balancing for each zone to maintain consistent room temperature
- Light Commercial Spaces
Projects: Offices, showrooms and small retail premises
Configuration: 4–12 circuits based on site layout
Value: Independent zone control, reduce heat supply for unoccupied zones to cut operation cost
- Heating Retrofit & Renovation Projects
Projects: Retrofitting existing buildings with underfloor radiant heating
Configuration: Custom circuit quantity according to building layout
Value: Modular design simplifies renovation work. Single loop maintenance can be performed without draining the whole heating system
Installation & Commissioning Guide
-
Installation Steps
- Install mounting brackets and fasten onto wall with suitable anchor bolts
- Mount supply bar and return bar onto brackets
- Use spirit level to ensure manifold horizontal installation
- Connect main supply and return pipelines
- Link each heating circuit to manifold branch ports
- (Optional) Install thermal electric actuators on return bar valve seats
-
Commissioning & Hydraulic Balancing
- Fill the whole heating system and eliminate air pockets
- Vent trapped air via air vent valve
- Fully open all supply and return regulating valves
- Calculate target flow rate of each circuit based on heat loss calculation
- Pre-set supply valves of each circuit to approximate target opening
- Fine tune return valves to reach designed flow
- Measure indoor temperature to confirm every room reaches target temperature
- Record valve opening position for future maintenance reference
-
Critical Notes
- Do not arbitrarily adjust valves after hydraulic balancing; keep valve position records
- Follow professional heat loss calculation for flow setup, avoid empirical guesswork
- Complete pressure test and joint leakage inspection before system commissioning
Maintenance Guidelines
-
Routine Inspection Schedule
| Task | Frequency |
|---|---|
| Visual inspection for leakage on joints | Quarterly |
| Valve operation inspection | Annually |
| Manifold surface cleaning | On demand |
| EPDM gasket inspection | Every 5–8 years |
-
Gasket Replacement (When Leakage Occurs)
- Close the isolation valve of corresponding circuit
- Remove the old EPDM sealing gasket
- Clean the sealing contact surface
- Fit new sealing gasket
- Reopen isolation valve and carry out pressure leakage test
-
Thermal Electric Actuator Maintenance (For systems fitted with actuators)
- Check actuator operation status once per year
- Confirm NO / NC type matches thermostat configuration
- Replace actuators that cannot fully open or close
FQA
Q: What is a double‑regulating manifold?
A: A heating manifold with regulating valves on both the supply and return bars for each circuit. This provides finer flow control than single‑regulating manifolds.
Q: What is the difference between this and a flow meter manifold?
A: Flow meter manifolds have transparent meters that show flow rate in real time. Double‑regulating manifolds do not have meters - they rely on temperature feedback and valve adjustment. Double‑regulating is more economical.
Q: How many circuits can I have?
A: 2‑12 circuits per manifold. Additional manifolds can be used for larger systems.
Q: What size is the manifold body?
A: DN25, which matches standard boiler connections for residential radiant heating.
Q: What is the pressure rating?
A: PN16 (1.6 MPa / 16 bar).
Q: What is the temperature range?
A: 5°C to 90°C.
Q: Are actuators included?
A: Actuators are optional accessories. The return bar has pre‑mounted valve seats that accept standard thermal electric actuators.
Q: What pipe sizes are compatible?
A: 16×2.0mm and 18×2.0mm PEX or PE‑RT pipes via compression fittings.
Q: Do you offer samples?
A: Yes, MOQ is 1 unit.
Q: What is the lead time?
A: 15 working days.
Products Summary
Yunnl dual‑regulating forged brass underfloor heating manifold delivers reliable hydraulic distribution and manual balancing for hydronic radiant heating projects. With flexible circuit selection from 2‑way to12‑way, rich accessory options and full compliance with European heating component standards, it serves housing renovators, plumbing distributors and commercial heating system integrators globally.
Hot Tags: double-adjustable floor heating manifold, China double-adjustable floor heating manifold manufacturers, suppliers, factory, Intelligent hydronic manifold, tainless steel water distributor, Stainless Steel Manifolds, Intelligent Floor Heating Manifold, Forged Integrated Ball Valve Floor Heating Manifold, Manifold with integrated flowmeter
