Equal Diameter Elbow Sliding Fastener

Equal Diameter Elbow Sliding Fastener

Details
The equal-diameter elbow sliding tension fitting is a pipe component used in pipeline systems to connect two pipes of the same diameter at a 90-degree bend. It achieves rapid and reliable pipe connection through sliding tension technology while ensuring excellent sealing performance.
Category
Sliding Fasteners
 
Send Inquiry
Description
Technical Parameters

Equal Diameter Elbow Sliding Fastener

 

The Open Flame Problem in Piping Installation

Welding and soldering have been the standard methods for pipe connection for decades. But they carry inherent risks and limitations:

Method Risk Limitation
Welding Open flame, fire hazard, toxic fumes Requires certified welder, hot work permit
Soldering Open flame, flux fumes Requires ventilation, fire watch
Threading None Thread damage, slow, requires sealing tape
Adhesive bonding Chemical exposure Long curing time, temperature sensitive

Press-fit technology eliminates these problems. The connection is made by mechanical compression - no heat, no flame, no fumes, no curing time. The pipe is inserted, the tool is activated, and the joint is complete in seconds.

Press-fit elbows are the directional-change component of this system. Available in 90° (standard) and 45° (gentle turn) configurations, they connect two pipes of identical diameter with no diameter reduction.

Feature Press-Fit (This Product) Welded Joint Threaded Joint
Heat required No Yes No
Fire risk None High None
Installation time 10 seconds 15-30 minutes 5-10 minutes
Skill level Basic Certified welder Moderate
Post-inspection Visual + gauge X-ray or dye Visual
Quality consistency Tool-calibrated Operator-dependent Operator-dependent
Best for Fire-restricted areas, speed Permanent, high-pressure General plumbing

 

Product Overview

Yunnl press-fit elbow is a mechanical compression fitting for changing pipe direction by 90°. Both ends accept pipes of identical diameter. The connection is made by inserting the pipe into the fitting socket and applying a press tool - the tool compresses the fitting body onto the pipe, deforming the built-in sealing ring against the pipe wall.

No welding. No threading. No adhesive. No open flame.

Available in three material options to match different media and operating environments:

Material Grade Best For
Stainless Steel SS304 Drinking water, industrial corrosive media
Stainless Steel SS316 Coastal, high-chloride, chemical
Copper C12200 HVAC heating and cooling piping

 

Key Advantages

  • No Open Flame - Fire-Restricted Area Installation

The press-fit connection requires no welding fire on site. This satisfies fire safety management requirements for high-rise buildings, shopping malls, factory workshops, and other fire-restricted areas where hot work permits are difficult to obtain.

  • Reliable Sliding Press Connection Structure

Built-in sliding rings and convex sealing rings are integrated at both connection ports. During installation, the sealing structure compresses tightly against the pipe outer wall via manual or hydraulic pressing tools. The mechanical interlocking structure provides lasting fixing force, preventing pipe loosening under water hammer, temperature variation, or pipeline vibration.

  • Multiple Material Options for Different Working Conditions

To adapt to diverse media and operating environments, Yunnl press-fit elbows support customizable raw materials:

Material Corrosion Resistance Temperature Range Best Application
SS304 Excellent -20°C ~ 110°C Drinking water, industrial corrosive media, high-temperature pipeline
SS316 Superior (chloride) -20°C ~ 150°C Coastal, chemical, marine
Copper Good -20°C ~ 120°C HVAC heating and cooling pipelines
  • Tool-Assembled, No Consumables

Installation requires only a press tool and matching jaws. No welding rod, no flux, no thread tape, no sealant, no adhesive. The sealing ring is pre-installed at the factory.

  • Full-Bore Flow Path

The internal diameter matches the pipe diameter. No flow restriction, minimal pressure drop across the fitting.

  • Visual Verification

After pressing, joint quality is verified through:

  1. Marking line visibility - confirms full insertion
  2. Gauge check - confirms jaw closure
  3. Visual inspection gap - confirms compression

 

18

 

Specifications

Feature Description

Place of origin

China

Brand name

Yunnl

Product Name

Equal Diameter Elbow Sliding Fastener
Optional Material SS304, SS316, Copper
Connection Type Sliding Press / Crimp Connection
Application Pipe PEX / PERT / Copper Pipe
Sealing Element EPDM / FKM O-ring (pre-installed)
Connection Type Sliding press / Crimp connection
Compatible Pipe PEX / PERT / Copper (specify O.D. and wall thickness)
Nominal Pressure PN16 (1.6 MPa)
Working Temperature -20°C ~ 110°C (EPDM) / -15°C ~ 150°C (FKM)
Applicable Medium Water, heating water, glycol, compressed air, non-corrosive fluids

Minimum Order Quantity

1

Price

Negotiable

Packing

Yunnl standard packing

Payment Terms

L/C, D/A, D/P, T/T, Western Union,MoneyGram

Delivery Time

15 Days

 

Working Principle: How the Sliding Press Connection Forms

Step Action Result
1 Insert the pipe into the fitting socket Pipe contacts the internal stop
2 Position the press jaw over the fitting Jaw aligned perpendicular to axis
3 Activate the press tool Radial compression applied
4 Fitting body deforms onto the pipe Mechanical interlock formed
5 Sealing ring compresses Leak-tight seal created

The entire connection forms a permanent sealed joint without additional sealant. Stable sealing performance is maintained under normal working pressure.

Comparison: 90° vs. 45° Elbow

Feature 90° Elbow 45° Elbow
Bend angle Right angle Gentle turn
Pressure drop Moderate Lower
Application share ~75% ~15%
Best for Standard risers, branches, wall transitions Gradual routing, offset connections
Space requirement Compact Moderate

 

Application Scenarios

  • Residential Water Supply & Drainage

Use case: Hot and cold potable water distribution in residential buildings.
Installation: 90° elbow at riser-to-branch connections.
Value: No open flame in occupied buildings. Fast installation for large projects.

  • HVAC Heating & Central Air Conditioning

Use case: Heating water and chilled water piping networks.
Installation: 45° elbow for low-pressure-drop runs; 90° for standard turns.
Value: No fire risk in mechanical rooms. Fast installation for large buildings.

  • Fire Protection Sprinkler Systems

Use case: Wet pipe sprinkler branch lines.
Installation: 90° elbow for standard sprinkler layouts.
Value: No hot work permit required. Fast installation in occupied buildings.

  • Industrial Fluid Transmission

Use case: Process cooling water, non-corrosive fluid lines.
Installation: 90° or 45° elbow depending on layout.
Value: Corrosion-resistant stainless steel. No fire risk in process areas.

  • Commercial Complex & High-Rise Buildings

Use case: Plumbing renovation and new construction.
Installation: Various elbows for riser and branch connections.
Value: Press-fit system speeds up construction. No fire watch required.

  • Factory Workshop Piping

Use case: Compressed air and process water lines.
Installation: 90° elbow for distribution networks.
Value: Fast installation without interrupting factory operations.

 

Installation Guide

  • Tools Required

Tool Purpose
Press tool Battery-powered or hydraulic
Press jaws Matching the elbow size
Pipe cutter Rotary style - not abrasive wheels
Deburring tool Internal/external chamfering
Depth marker Oil-based marking pen
Go/no-go gauge Verify pressed joint
  • Installation Steps

  1. Cut the pipe - Square cut, perpendicular to axis
  2. Deburr - Remove internal and external burrs (critical for sealing ring protection)
  3. Mark insertion depth - Oil-based marker
  4. Inspect sealing ring - Confirm seated, not twisted or contaminated
  5. Insert the pipe - Push until marking line aligns with socket edge
  6. Position the press jaw - Perpendicular to axis, over the fitting bulge
  7. Press - Activate the tool until the jaw fully closes
  8. Verify - Go/no-go gauge check; visual inspection of compression
  • Important Notes

  1. Do not use abrasive cutting wheels - Abrasive residue causes corrosion
  2. Deburr both inside and outside - Burrs damage the sealing ring
  3. Do not use oil or grease for insertion - Moistening with clean water is acceptable
  4. Do not over-press - One complete press is sufficient
  5. Pipe must bottom out - Incomplete insertion causes leakage

 

FAQ

Q: What pipes are compatible with this press-fit elbow?

A: PEX, PERT, and copper pipes. Specify pipe O.D. and wall thickness when ordering. Not suitable for steel or PPR pipes.

Q: Does the press-fit elbow need glue or welding during installation?

A: No. The connection is made by mechanical compression using a press tool. No adhesive, no welding, no open flame.

Q: What is the pressure rating?

A: PN16 (1.6 MPa / 16 bar).

Q: What is the temperature range?

A: -20°C to 110°C with EPDM seals. Up to 150°C with FKM seals.

Q: What materials are available?

A: SS304, SS316 stainless steel, and copper. Choose based on media and environment.

Q: Can the connection be disassembled?

A: Press-fit joints are permanent. Disassembly requires cutting the pipe. For serviceable connections, install a union or threaded adapter nearby.

Q: How is correct installation verified?

A: Three methods: marking line visible at socket edge; go/no-go gauge confirms jaw closure; visual inspection shows uniform compression.

Q: Why choose Yunnl press-fit pipe fittings?

A: Yunnl offers three material options (SS304, SS316, copper), factory-installed sealing rings, and tool-calibrated joint quality. The press-fit system eliminates open flame for fire-restricted areas.

Q: Are samples available?

A: Yes, MOQ is 1 unit. Sample orders are supported for quality and dimension verification.

Q: What is the lead time?

A: 15 working days.

 

Closing Summary

Yunnl press-fit elbow provides fast, reliable 90° and 45° directional changes for PEX, PERT, and copper piping. Sliding press connection - no welding, no threading, no adhesive, no open flame. Available in SS304, SS316, and copper, DN15-DN50, PN16 rating, -20°C to 150°C. Suitable for water supply, HVAC, fire protection, and industrial fluid transmission. Sample support, 15-day delivery and flexible payment terms.

 

Hot Tags: equal diameter elbow sliding fastener, China equal diameter elbow sliding fastener manufacturers, suppliers, factory, Compression-style equal diameter straight connectorh, pipe fittings, Inner Ribbon Elbow, Equal Diameter Male Threaded Tee Fitting, Equal Diameter Elbow Sliding Fastener, Female Thread Elbow Sliding Fastener

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!