Female Thread Elbow Sliding Fastener

Female Thread Elbow Sliding Fastener

Details
An internal thread elbow is an elbow fitting with internal threads, typically at 90° or 45°, used to change the direction of pipelines. It connects with other external thread fittings (such as external thread straight connectors, valves, etc.) through its internal threads.
Category
Sliding Fasteners
 
Send Inquiry
Description
Technical Parameters

Female Thread Elbow Sliding Fastener

 

Female-Thread Elbow Sliding Fastener vs Ordinary Thread-Only Elbow Comparison

Conventional pure-thread elbow only provides threaded transition. To connect plastic, copper or stainless-steel pipe, extra adapters or welding operations are required, which adds joints and potential leakage-points.

Female-thread elbow sliding fastener is 90°/45° directional elbow combining female-thread port and slide-tight crimp-connection. One end female-thread docks male-thread components; the other end adopts slide-tight mechanism for pipe connection. No welding needed, supports disassembly for overhaul, reduces intermediate adapters for pipe-direction-change layout.

Item

Ordinary Thread-Only Elbow

Female Thread Elbow Sliding Fastener (This Product)

Connection mode

Pure threaded connection

Female-thread port + slide-tight crimp port

Pipe-material connection

Need extra adapters / welding

Direct for plastic / copper / stainless-steel pipe

Welding requirement

May need welding for metal pipe

Welding-free assembly

Disassembly for maintenance

Usually requires pipe-cutting

Demountable without pipe-cutting

Sealing form

Thread + external tape/gasket

Dual-seal: slide-ring mechanical compression + elastic sealing-ring

Typical usage

Pure-thread pipeline direction-change

Mixed-material pipeline corner transition

 

Product Overview

Yuanlun female-thread elbow sliding fastener is directional slide-tight elbow fitting, available in 90° or 45-degree angle. One-end female internal thread connects external-thread fittings/valves; the other-end is slide-tight crimp-port for plastic pipe, copper pipe or stainless-steel pipe.

Optional material: copper, stainless-steel, PPR. Adopts slide-tight push-fit connection mechanism, no-welding quick assembly, demountable structure. PN16 nominal pressure-rating, working-temperature 5℃-90℃. Widely-applied for plumbing, HVAC and light-industrial hydraulic piping-systems.

Important note: Installation recommended to be completed by qualified plumbing technicians. Must use matched dedicated slide-tight crimping-tool. Pipe-end must be squarely cut and deburred; burr will damage sealing-ring and cause hidden leakage risk.

 

Key Advantages

  • Premium-Material Durability

Constructed from high-quality copper / stainless-steel / PPR optional materials. Excellent corrosion-resistance, high mechanical strength and wear-resistance, guarantees long-term stable performance under multiple harsh working-environments.

  • Smooth Flow-Redirecting & Reliable Connection

90° /45° elbow structure realizes smooth fluid direction-change. Female-thread and slide-tight double-connection structure achieves tight leak-proof joint, optimizes medium conveying efficiency.

  • Convenient Installation & Maintenance

Slide-tight mechanism supports quick assembly and disassembly. According to variant type: press-fit type requires special crimping pliers; push-to-connect quick-connect version can assemble without special tools. Greatly improves site-operation efficiency and shortens maintenance time.

  • Broad-Range Application Versatility

Suitable for industrial pipelines, building plumbing and hydraulic-circuit systems. Flexible to adapt diversified pipeline layout and various non-corrosive-medium requirements.

 

19

 

Specifications

Feature

Description

Place of origin

China

Brand name

Yunnl

Product Name

Female Thread Elbow Sliding Fastener

Size

DN15-DN50

Body Material

Copper / Stainless-steel / PPR optional (to confirm material grade)

Sealing Parts

Elastic O-ring + slide-tight compression slide-ring

Thread Standard

ISO228 BSP female-thread as standard; NPT customizable

Angle Option

90° / 45° elbow

Nominal Pressure

PN16 (1.6 MPa), PN25 optional

Working Temperature

5℃ ~ 90℃

Compatible Pipe Material

Plastic pipe, copper pipe, stainless-steel pipe

Operation Mode

Female-thread screw assembly + slide-tight crimp-tool / tool-free push-in connection

Minimum Order Quantity

1

Price

Negotiable

Packing

Yuanlun standard packing

Payment Terms

L/C, D/A, D/P, T/T, Western Union, MoneyGram

Delivery Time

15 Days

 

Working Principle

  • Main Components & Function

Component

Core Function

Elbow main-body

90°/45-degree flow-direction-change; integrates female-thread port and slide-tight port

Female-thread port

Threaded docking for male-thread fittings, valves and pipe-components

Slide-tight slide-ring

Axial push-in component, generates radial squeezing force on outer pipe wall

Elastic O-ring

Compression-deformation fills clearance between pipe and fitting inner-cavity for leak-proof sealing

  • Operating Principle

  • Female-thread end connection: Align elbow female-thread with mating male-thread component, screw-in and tighten to proper torque.
  • Slide-tight port connection: Insert squarely-cut, deburred pipe end into slide-tight sleeve. For press-fit variant: use matched special crimp-pliers to push slide-ring in-place; for push-connect variant: directly insert pipe in-position without tool.

Slide-ring produces radial compression force; O-ring deforms elastically to fill gaps, forming dual-protection sealed joint.

For maintenance: Disassemble slide-tight joint without cutting the connected pipe.

Operating reminder: Press-fit slide-tight variant must use matched crimp-pliers. Improper tool leads to incomplete crimping and hidden leakage risk.

 

Application Scenarios

  • Residential & Commercial Plumbing Systems

Use-case: Pipeline corner direction-change joints for cold-hot-water supply networks. Project value: Multi-material adaptability, welding-free erection, convenient for renovation-project construction.

  • HVAC Heating-Ventilation-Air-Conditioning Systems

Use-case: Corner transition for heating-loop and air-conditioning circulating-water pipelines. Project value: Elbow smooth runner reduces local flow-resistance; slide-tight structure adapts temperature-cycling working-conditions.

  • Hydraulic Auxiliary Circuits

Use-case: Direction-change connection for low-pressure hydraulic auxiliary pipelines. Project value: High-strength stainless-steel variant optional for demanding hydraulic-working-conditions.

  • Light-Industrial Process Piping

Use-case: Corner transition joints for industrial non-corrosive-liquid pipelines. Project value: Multiple-material selection meets different anti-corrosion and pressure-grade requirements.

 

Selection and Installation Recommendations

  • Material Selection

  1. Copper: Good corrosion-resistance, suitable for cold-hot-water systems.
  2. Stainless-steel: High mechanical strength, fit for high-pressure working-conditions.
  3. PPR: Cost-effective solution, applicable for low-temperature water-systems.
  • Size Matching

  1. Confirm thread specification (G1/2, G3/4 etc.) and pipe outer-diameter.
  2. Ensure nominal pressure rating (PN16 / PN25) matches system design-requirements.
  • Installation Tools

  1. Press-fit slide-tight type: Mandatory use matched special crimping pliers.
  2. Quick push-connect type: Require squarely-cut, deburred pipe-end to avoid scratching sealing-O-ring.

 

Installation Guide

  • Pre-Installation Check

  1. Confirm elbow DN-size, angle-spec, thread and material variant match project requirements. Prepare matched tool according to fitting type (press-fit / push-connect).
  2. Inspect elbow body, slide-ring and O-ring; reject cracked, scratched or ageing spare-parts.
  3. Square-cut pipe-end; fully remove burr, chips and sharp edges. Burr will damage elastic O-ring.
  • Installation Steps

  1. For female-thread end: Wind PTFE-tape 3-5 clockwise-turns on mating male-thread component. Screw elbow onto fitting; apply wrench-torque only on elbow body flats. Do NOT apply torque on slide-tight sleeve section.
  2. Put slide-ring and O-ring onto pipe following correct sequence. Insert pipe fully into elbow slide-tight sleeve until inner stop shoulder.
  3. Press-fit-variant: Mount matched crimp-pliers, complete crimp-stroke to push slide-ring to designated position. Push-connect-variant: Firmly push pipe fully in-position.
  4. Reserve enough clearance for pipeline thermal-displacement.
  5. After full assembly completion, slowly pressurize system, inspect female-thread joint and slide-tight crimp-port for leakage.
  • Important Installation Notes

  1. Installation recommended for qualified plumbing technicians.
  2. Press-fit slide-tight elbow must adopt matched crimp-pliers; mismatched-tool will cause sealing-failure.
  3. Pipe-end must be square and deburred; burr scratches O-ring will bring hidden leakage risk.
  4. Do not reuse deformed O-ring during reassembly; replace with brand-new spare-part.

 

Maintenance & Troubleshooting

Phenomenon

Probable Root-Cause

Recommended Solution

Loose sliding tension-connection

Ageing O-ring; insufficient pipe insertion-depth; improper crimp-tool

Replace brand-new O-ring; re-confirm pipe insertion-depth; re-execute complete crimp-operation

Thread-interface leakage

Insufficient Teflon-tape wrapping; thread scratch / damage

Re-wrap PTFE-tape or apply thread-sealant; replace damaged elbow component

Stiff slide-ring movement

Scale or foreign-debris inside slide-tight sleeve

Disassemble fitting, clean inner-cavity and slide-ring

Routine-Maintenance Suggestion

  • Visual inspection of thread-joint and slide-tight port for leakage: Quarterly
  • Check slide-ring fastening state during system overhaul: Annually
  • Replace ageing O-ring spare-parts upon leakage-failure: As-required

 

 

FAQ

Q: Can this slide tight elbow compensate large scale pipeline thermaldisplacement?

A: It only allows minor displacement inside slide tight sleeve. Large thermal expansion needs independent expansion absorbing components.

Q: Can press fit slide tight joint be disassembled and reused?

A: The fitting body can be reused, but O-ring must be replaced with new spare part; slide ring may produce plastic deformation after crimping, inspect condition before reuse.

 

Products Summary

Yuanlun female-thread elbow sliding fastener is 90°/45-degree directional slide-tight elbow fitting, PN16-PN25 optional pressure-rating, DN15-DN50 size-range. One-side female-thread port, one-side slide-tight crimp-connection; copper / stainless-steel / PPR multi-material optional. Welding-free assembly, demountable without pipe-cutting. Widely-applied for building plumbing, HVAC, low-pressure hydraulic and light-industrial non-corrosive-fluid piping-systems. Sample-order supported for pre-project-evaluation, 15-day standard lead-time for worldwide plumbing-HVAC distributors and engineering-contractors.

 

Factory Information

Zhejiang Yuanlun Valve Co., Ltd. was founded in 2006, formerly known as Yuhuan Guohong Valve Co., Ltd. It is located in Yuhuan, Zhejiang Province, known as the "Valve Capital of China". After nearly two decades of stable development, Yuanlun Valve is a professional manufacturer for HVAC valves integrating R&D, production and sales. Our product portfolio covers floor heating systems, air-conditioning systems, domestic water valves, including ball valves, thermostatic valves, manifolds, check valves, stop valves, filter valves, angle valves, pipe fittings, corrugated pipes and other series.

 

Hot Tags: female thread elbow sliding fastener, China female thread elbow sliding fastener manufacturers, suppliers, factory, Compression-style equal diameter straight connectorh, pipe fittings, Inner Ribbon Elbow, Equal Diameter Male Threaded Tee Fitting, Equal Diameter Elbow Sliding Fastener, Female Thread Elbow Sliding Fastener

Send Inquiry
Contact us if have any question

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.

Contact now!